View SPPOSC_4364102.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SPPOSC Series
2" X 2" (Low Distortion) 1 Hz to 102.4 kHz 8 or 9-Bit Frequency Selectable
Description
The SPPOSC Series is a compact, dual channel, phase continuous, DSP based, programmable sine wave generator with analog outputs and 8 or 9 bits of frequency selection. All SPPOSC-01 platforms are small, low profile, easy to use signal generators, which require no external components and can cover the audio/ultrasonic bandwidth from 1 Hz to 102.4 kHz in several standard and custom frequency ranges. SPPOSC's use a fixed point DSP with 32-bit math, 24bits of resolution and dual channel DACs. Noise floor and distortion are typically -100dB to 20 kHz and < - 80 dB to 100 kHz.
Oscillators: Dual Channel & Quadrature
Features/ Benefits:
* Available in a single, dual or quadrature (0.1 phase stability) form factor, SPPOSC oscillators with up to 512 tuning steps insure design flexibility in a compact 2" x 2" footprint while minimizing board space requirements. This plug-in, turnkey signal source, with a standard or custom algorithm, allows product designers to incorporate various precision onboard programmable signal generators in a standard pin-out and form factor thereby reducing design time while maximizing design flexibility. When used in conjunction with the SPPDB-01 development board, SPPOCS signal generators require minimal set-up time to provide low noise and distortion signals for laboratory evaluation or precision field installations.
*
OSCILLATOR SOFTWARE SELECTION GUIDE
SPPOSC-01
SWDO-01 SWDO-02 SWQO-01 SWQO-02 SWSO-01 SWSO-02
*
Low Frequency Ranges
Dual Chl. Prog. Osc. 1 Hz - 256 Hz, 1 Hz Steps Dual Chl. Prog. Osc. 10 Hz - 2.56 kHz, 10 Hz Steps Quadrature Prog. Osc. 1 Hz - 512 Hz, 1 Hz Steps Quadrature Prog. Osc. 10 Hz - 5.12 kHz, 10 Hz Steps Same Prog. Dual Chl. Osc. 1 Hz - 512 Hz, 1 Hz Steps Same Prog. Dual Chl. Osc. 10 Hz - 5.12 kHz, 10 Hz Steps
Applications
* * * * Low distortion signal source for ATE systems Sound and vibration testing Quadrature signal generator: sine / cosine, standard or custom. Tone generation in speech and hearing analysis, research, pathology
Exam ple Quadrature Oscillator
Analog Filters Dual D/A Converters Digital Filters
Program m em ory EE-Prom Frequency select bus
SPPOSC-02
SWDO-03 SWDO-04 SWDO-05 SWQO-03 SWQO-04 SWSO-03 SWSO-04
High Frequency Ranges
Dual Chl. Prog. Osc. 100 Hz - 25.6 kHz,100 Hz Steps Dual Chl. Prog. Osc. 200 Hz - 51.2 kHz, 200 Hz Steps Dual Chl. Prog. Osc. 400 Hz - 102.4 kHz, 400 Hz Steps Quadrature Prog. Osc. 100 Hz - 51.2 kHz, 100 Hz Steps Quadrature Prog. Osc. 200 Hz - 102.4 kHz, 200 Hz Steps Same Prog. Dual Chl. Osc. 100 Hz - 51.2 kHz, 100 Hz Steps Same Prog. Dual Chl. Osc. 200 Hz - 102.4 kHz, 200 Hz Steps
Analog I/O
Sine Cosine
Digital Signal Processor
CUSTOM SW
SWDO-CXX
3 wire digital output bus
Custom Frequency Ranges
Custom Dual Chl. Prog. Oscillator Custom Quadrature Prog. Oscillator Custom Same Prog. Dual Chl. Oscillator
SWQO-CXX SWSO-CXX
1
1784 Chessie Lane, Ottawa, IL 61350 * Tel: 800/252-7074, 815/434-7800 * FAX: 815/434-8176 e-mail: sales@freqdev.com * Web Address: http://www.freqdev.com
SPPOSC Series
2" X 2" (Low Distortion) 1 Hz to 102.4 kHz 8 or 9-Bit Frequency Selectable
Frequency Selection Data Port Data Format * Logic "0" * Logic "1"
Oscillators: Dual Channel & Quadrature
9-Bit Programming Table
0VDC Min - 2VDC Max 3.5VDC Min - 5Vdc Max
MSB 28 D8 0 0 0 0 0 0 0 0 0 1
--27 D7 0 0 0 0 0 0 0 0 1 1
--26 D6 0 0 0 0 0 0 0 1 1 1
--25 D5 0 0 0 0 0 0 1 1 1 1
--24 D4 0 0 0 0 0 1 1 1 1 1
--23 D3 0 0 0 0 1 1 1 1 1 1
--22 D2 0 0 0 1 1 1 1 1 1 1
--21 D1 0 0 1 1 1 1 1 1 1 1
LSB 20 D0 0 1 1 1 1 1 1 1 1 1
Bit Weight fc Corner Frequency fmax/512 fmax/256 fmax/128 fmax/64 fmax/32 fmax/16 fmax/8 fmax/4 fmax/2 fmax
Bit Weighting (Binary Coded) LSB D0 MSB D7 or D8 (for 9-bits) Frequency: 256:1 (8-bit dual), or 512:1 (9-bit single) ____________________________________________ 1. The frequency selection data word bus consists of D0 to D7 for 8-bit programming and D0 to D8 for 9-bit programming. 2. For dual Channel 8-Bit programming D8 is Channel Select and requires a minimum of 21 secs set-up time at a logic "1", 5volts for channel 2 or logic "0", 0 volts, for Channel 1 3. For an 8-bit dual channel unit, the Program enable or "Latch pin" is D9. To enable a program change, this pin must be pulled to a logic high "1" or 5 volts. If the pin is low, a frequency change will not be read and the channels will continue to run the previous values.
8-Bit Programming Table
4. The D0 - D9 bus data are checked simultaneously. New frequency selection data must be present or updated at the time Channel select occurs to be valid. The Program enable or "Latch" pin must be high. While the latch pin is high, the Frequency data must remain on the bus until the user applies the next frequency change. The pins do not float during programming! The frequency ports are polled by the system every 21 seconds. Within 21 secs of programming, if the latch goes low, the programmed values are retained and the pins may float.
D9 Enable/Latch D8 Ch Sel D0 to D7 Frequency Select MSB 27 D7 0 0 0 0 0 0 0 0 --26 D6 0 0 0 0 0 0 0 1 1 --25 D5 0 0 0 0 0 0 1 1 1 --24 D4 0 0 0 0 0 1 1 1 1 --23 D3 0 0 0 0 1 1 1 1 1 --22 D2 0 0 0 1 1 1 1 1 1 --21 D1 0 0 1 1 1 1 1 1 1 LSB 20 D0 0 1 1 1 1 1 1 1 1 Bit Weight fc Corner Frequency fmax/256 fmax/128 fmax/64 fmax/32 fmax/16 fmax/8 fmax/4 fmax/2 fmax
Tsu 21 secs min
DATA VALID
1
2
1784 Chessie Lane, Ottawa, IL 61350 * Tel: 800/252-7074, 815/434-7800 * FAX: 815/434-8176 e-mail: sales@freqdev.com * Web Address: http://www.freqdev.com
SPPOSC Series
2" X 2" (Low Distortion) 1 Hz to 102.4 kHz 8 or 9-Bit Frequency Selectable
SPPOSC-01 & 02
Performance Specifications
Available Tuning Range 1.00 Hz to 102.4 kHz < 0.05 % < 0.1 dB < -100dB Max., -105dB Typ.
Oscillators: Dual Channel & Quadrature
Specifications
(@25C and Vs = 15 Vdc) Analog Output Characteristics Minimum load Impedance 10 k Maximum capacitive load 50 pF. Output voltage 5 V peak (sine wave) Offset Voltage 2 mV Typ. 10mV Max. Power Supply (Vs) Analog Vs range 10Vdc Min to 15 Vdc Max. Analog supply current at Max. Vs 17 mA Typ. Digital PS Voltage +5 Vdc Digital supply current 150 mA Typ. Power consumption at Max. Vs 1.5 watts Max.
Frequency Accuracy Amplitude Accuracy Total Broad Band Noise
(Ref to 3.53 VRMS)
Total Harm. Dist.(THD)
(10V peak to peak)
<-100 dB Max. to 20 kHz < - 80 dB Max. to 102.4 kHz < 0.10 1 Hz -10K < - 100 dB Typ. 10kH - 100K < - 90 dB Typ.
Channel to Channel phase tracking (SWDO-01 to 05) Cross talk dual channel version with different frequencies on each channel.
Care must be taken to stay above the minimum Vs in order to maintain the linearity and distortion performance of the oscillator.
Temperature Operating Storage Size
0 to +70oC -25 to +85oC 2.0" x 2.0" x 0.5"
There are three software configurations available for these SPPOSC-01 / -02 oscillators. Software Options: 1. SWDO-01 to -05: Dual channel with independently selectable frequencies. 2. SWSO-01 to -04: Dual Channel, same output and same frequency selection. 3. SWQO-01 to -04: Quadrature, single frequency selection and Sine/Cosine outputs. All configurations are available with custom frequency selections. Consult factory for a quotation. These special programs will be assigned a custom suffix (CXX) at the time of order.
A socketed development board (SPPDB-01) can double as an oscillator mounting assembly, to facilitate product evaluation or laboratory use. The SPPDB-01 development board is specified and sold separately.
3
1784 Chessie Lane, Ottawa, IL 61350 * Tel: 800/252-7074, 815/434-7800 * FAX: 815/434-8176 e-mail: sales@freqdev.com * Web Address: http://www.freqdev.com
SPPOSC Series
2" X 2" (Low Distortion) 1 Hz to 102.4 kHz 8 or 9-Bit Frequency Selectable
2.0"
0.25" 0.075" 0.20"
Oscillators: Dual Channel & Quadrature
FACTORY OR CUSTOM USE ONLY SCLK LRCLK SDIN MCLK
+5V DGND FACTORY OR CUSTOM USE ONLY
0.275" 0.275"
D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 OUT2 AGND OUT1 -15V AGND +15V
DGND NOT USED NOT USED
2.0"
0.10"
Frequency Select Port
NOT USED SPI-CS-EEPROM SPI-SO SPI-SI SPI-SCK SPI-/WP
0.20"
0.40"
Outputs and Analog PS
0.125" 0.05"
0.085 " 0.065 "
0.125" 0.05"
NOT USED NOT USED AGND NOT USED NOT USED
SPPOSC TOP VIEW PIN IDENTIFICATION
0.15 " 0.160 " Min.
0.46" 0.31 "
PIN CLEARANCE PIN DIA. 0.025"
SPPOSC TOP VIEW AND DIMENSIONS All normal pin spacing 0.10"
D0 - D7or 8 D8 D9 Out 1 & 2 15 Vdc + 5 Vdc A Gnd D Gnd
8 or 9 - bit Frequency select pins Channel select for 8 bit dual Osc. Enable / Latch for 8 bit dual Osc. Oscillator outputs Analog Dc power In Digital Power In Analog Ground Digital Ground
ORDERING INFORMATION
S P P O S C - 01 / S W Q O - 01
0 1 L o w F re q . ra n g e 0 2 H ig h F re q . ra n g e O sc illa to r S o ftw a re typ e e xa m p le S W Q O (Q u a d ra tu re ) SW DO Dual channel S W S O S a m e fre q d u a l S e le c ta b le F re q u e n c y ra n g e e xa m p le -0 1 (1 H z to 5 1 2 H z) S e e S e le c tio n g u id e fro n t p a g e .
Consult factory for custom non-standard frequencies and ranges. The SPPDB - 01 Mounting Assembly is available for this Oscillator.
We hope the information given here will be helpful. The information is based on data and our best knowledge, and we consider the information to be true and accurate. Please read all statements, recommendations or suggestions herein in conjunction with our conditions of sale which apply to all goods supplied by us. We assume no responsibility for the use of these statements, recommendations or suggestions, nor do we intend them as a recommendation for any use which would infringe any patent or copyright.
4
1784 Chessie Lane, Ottawa, IL 61350 * Tel: 800/252-7074, 815/434-7800 * FAX: 815/434-8176 e-mail: sales@freqdev.com * Web Address: http://www.freqdev.com

▲Up To Search▲

Price & Availability of SPPOSC

	To Download SPPOSC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .